Search Results for ‘issue’

Okay folks, need some Cluster help. It's been like this since I've owned the car. Issues are that the Needles are just slightly off where they're SUPPOSED to be. When my speedometer shows I'm traveling 60mph, I'm actually going around 54mph. As for as the Cluster test, this will show you how...

ok.. im clueless, so take it easy on me. i got in my car yesterday and havent noticed anything different than any other time. car is completely stock. if i am driving and turn the wheel 1/2 to the the left, my car makes a normal turn.. where if i turn the wheel to the right i feel a floating...

Hi, Car 04 coupe. I have installed some megan sport coilovers on my car. Just wondering if anyone with direct experience setting these up can give some help. My issue is that I think I've maxed out the rear height as low as they will go, but its not near where I'd like them to be at. I'd...

Ok, so my roommate and I swapped in a GSR motor into a 94 Civic Coupe DX. Previously, another owner had swapped in a LS-Vtec motor. Had a B18B1 block and a B16 head. The LS ran fine. The car is boosted with a t63 precision turbo and Hondata s300 on a p30 Ecu. The GSR is a B18C1. The car will...

I am looking for a 7/16" NPT to -3AN adapter as stated in http://beesandgoats.com/boostfaq/g2icturbo.html Which I am, I am using a 15g TD04H turbo. If anyone knows where I can locate one of these adapters, I would greatly appreciate it, I've looked all over.

Okay I went to unlock my car using the key fob and I hit the button and nothing happend so after a few tries I opened the door with the key and tried to use the power door switch and still nothing... I started the car up and the E-Brake light remained on even with the ebrake down and the over...

hey guys i just did a disk brake swap on my em2 never touched the front end. i have tein ss-p full coilovers and skunk2 front and back camber kit. after the disk install everything seemed fine until i was driving and my steering wheel is turn 10 degrees off centre. do i need another...

Hey Guys, Most of you guys know my color scheme issue. my car is two tone black top with SSM bottom. give some opinions. 1.all Black murdered out look 2. keep two tone. put OEM SSM hood paint lip SSM front and sides. 3. keep two tone with hood and paint sides and front. theres tons more...

So I have searched, with no luck, on what procedure to take when replacing my wheel bearings. I need both front and rear, and was curious do I just need bearings, or do I replace the entire hub assembly? Thanks

Hello I have a 2004ex. A whyll back i bought some dezod front pads.I was going to use them on the circuit but i ran in some problem getting them in the caliper! 1.width of the dezod pads is 1mm larger, i would have to file them off. 2.Pad surface is almost 1cm smaller than my stock pads...

i broke one of the screws for piece number 11. anyone want to suggest how to fix this issue?

So I'm trying to put my passenger-side axle back in, and it's giving me fits. The LCA won't lower down enough to put the knuckle back in it for some reason, the compliance bushing is holding it about horizontal. What's the best way to deal with this? I've got a buddy coming over later and...

Just put in a bran new Hitachi alternator into my 1991 Mazda Protege 1.8 DOHC. Well, the alternator came out and went in smoothly, but when I started up the car, the belt was squealing. The belt looks in decent shape so I played around with the tension and got on the throttle a bit and once...

I just installed some Neuspeed Sport Springs, and while checking for front clearance by turning the wheel i noticed the springs turn as well. Is this normal?

Ok this just started today on my way to lunch... the shifting became very hard... like I had to force it into gear... it wasnt griding but I had to actually put force into it... and usualy i dont... what could be causing this...

Heres the situation, My car is raised on jacks, the rear tire/wheel is removed, the e brake is down, if I try to spin the rotor/disc - it does not freely spin - like it normally would. any ideas?

as some of you have seen in the "post your accident" thread, my toyota yaris was involved in an accident. the current market value of the vehicle is currently $13.5k and the total costs of repair is $7.7k. now, there is this thing called a diminished value (DV), which is basically the value of...

All right drag-minded folks, I'm headed to the strip on Saturday and need a little advice on shift points. I've been practicing my e-brake launches so I'm not worried about that. What I am curious about is when to shift. The first time I went, it was advised (after the fact) that I not shift...

so my friend installed fogs on his civic. he tapped into his headlight to get power for the fogs but he keeps blowing the in-line fuse for the fogs. im assuming the fogs are drawing too much current and he should just find a new power source. hes put a higher tolerant fuse (20A) in but it blows...